Hot Sale Rubber Banbury Internal Mixer-manufacture,factory,supplier from China

Vulcanizing autoclaves are used by the rubber industry to convert natural rubber into a cured and cross-linked vulcanized rubber product. Vulcanizing autoclaves can also be used to cure plastics. Vulcanizing autoclaves use live internal steam, a mix of live steam and hot air, or hot-air only. Vulcanizing autoclaves are used to cure tires, hoses, and many other products.Hydraulic system of vulcanizing tank: cover closing, cover locking and other actions in the operation of vulcanizing tank are completed by the hydraulic system.

The correct way of storage is: wash the rubber roller with clean water, then seal it with plastic film, preferably not to let it contact with air, then put it in a special storage place, do not fall east and west, affecting its internal mechanical properties and the quality of the rubber surface.The internal bearings and shaft head need to be well lubricatedWe suggest that in the daily situation, it is better to make some maintenance to the rubber roller used every week, and the lubrication of its rubber surface and internal must be good enough.

Press roller for copierHigh temperature resistant, wear-resistant, foam powder, etc.Used for various types of copiersSilicone rubber rollerHigh temperature resistant, non adhesive plastic, etc.For hot plastic resin adhesive bonded plastic woven collar lining cable etc.Butyl rubber rollerResistance to acetate, cyclohexanone and other medium, good air tightness)Used in leather, plastic and other industriesRubber roller CStrong acid strong alkali resistance, ozone resistance of 3 l: K S% X1 _!Used in printing and dyeing, metallurgy, plastics and other industriesThree ethylene propylene rubber rol

1. The first start after stopping for a long time should be carried out according to the requirements of the above-mentioned idling test and load test run. For the swing type discharge door, there are two bolts on both sides of the discharge door to prevent the discharge from opening when parked. Be sure to use the hydraulic system to place the discharge door in the closed position in advance, and use the locking device to lock the discharge door. At this time, turn the two bolts to a position that does not affect the opening of the discharge door.2. Daily starta.

The NBR Rubber Roller Covering Machine Hot Sale is intended and made for up the rubber covering process. applicable models will be elite for various industries.Advanced and mature technology can bring higher potency to the roller production.Applicable to production of Rubber Rollers in heavy industry, such as transmission rubber rollers in steel and steel deep processing industry,textile industry,printing and dyeing industry and so on.

Introduction of rubber extruderRubber extruder is a basic equipment in the rubber industry and one of the key equipments affecting product quality. It plays a very important role in the production process of tires and rubber products. The development of foreign rubber extruders has experienced a Plug extruder, screw type hot feed extruder, common cold feed extruder, main and auxiliary screw thread cold feed extruder, cold feed exhaust extruder, pin cold feed extruder, Compound extruder and other stages.

Press roller for copierHigh temperature resistant, wear-resistant, foam powder, etc.Used for various types of copiersSilicone rubber rollerHigh temperature resistant, non adhesive plastic, etc.For hot plastic resin adhesive bonded plastic woven collar lining cable etc.Butyl rubber rollerResistance to acetate, cyclohexanone and other medium, good air tightness)Used in leather, plastic and other industriesRubber roller CStrong acid strong alkali resistance, ozone resistance of 3 l: K S% X1 _!Used in printing and dyeing, metallurgy, plastics and other industriesThree ethylene propylene rubber rol

Rubber extruder is a basic equipment in the rubber industry and one of the key equipment that affects product quality. It plays a very important role in the production process of tires and rubber products. The development of rubber extruders abroad has gone through stages such as plunger extruders, screw type hot feed extruders, ordinary cold feed extruders, main and auxiliary thread cold feed extruders, cold feed exhaust extruders, pin cold feed extruders, and composite extruders. Rubber extruders are used for molding, filtering, and rubber wrapping of rubber semi-finished products.

A, the pressure between the rubber rollers is too heavy pressure between the rubber rollers will increase the friction between the rubber rollers, make the rubber rollers warm up and heat up, aggravate the squeeze expansion between the rubber rollers, accelerate the aging and deformation of the rubber rollers, accelerate the emulsification process of ink and water, which is not conducive to the transfer of ink.The solution is: the pressure between the rubber rollers should be basically the same as the pressure of the contact layout.

After vulcanization, rubber products often need some post-treatment before they can become qualified products.